Podcasts about adafruit

We got the drop that Sonnet 4 (https://www.anthropic.com/news/claude-4) just got released and the baby went to sleep early, so let's try it out! We wrote a library for the STSPIN220 (https://www.digikey.com/en/products/detail/stmicroelectronics/STSPIN220/6137574) — this is a stepper motor driver like the A4988 (https://www.adafruit.com/product/6109) or TMC2209 (https://www.adafruit.com/product/6121), but for low voltage motors. One interesting thing about it is it uses the step/dir and two mode pins to set the micro-steps, from 1 to 1/256. Since that gets a little confusing, we figured a driver (https://github.com/adafruit/Adafruit_STSPIN) would be worth doing. The table was definitely annoying to decode, and higher microsteps started overflowing 16-bit variables, but now we've got it spinning happily! #anthropic #claude #sonnet Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

LED Illuminated Pushbutton - 60mm Square (0:10) https://www.adafruit.com/product/6261?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts LED Illuminated Push Button - 51mm Square (0:10) https://www.adafruit.com/product/6270?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts LED Illuminated Push Button - 44mm Square (0:10) https://www.adafruit.com/product/6274?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts Blue USB Type C to USB A Cable with 540 Degree Rotating End - 2 meter long (3:11) https://www.adafruit.com/product/6279?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts Blue USB Type C to USB A Cable with 540 Degree Rotating End - 1 meter long (3:11) https://www.adafruit.com/product/6278?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts Adafruit OPT4048 Tri-Stimulus XYZ Color and Lux Sensor (4:42) https://www.adafruit.com/product/6335?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts ----------------------------------------- New nEw NEWs New Products, News, and more: https://www.adafruit.com/newsletter #newnewnew Shop for all of the newest Adafruit products: http://adafru.it/new Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

This week's EYE ON NPI is renowned world-wide, it's onsemi's ARX383CS 1/8-inch 0.3 Mp Global Shutter CMOS Digital Image Sensor (https://www.digikey.com/short/45p5vfvr), a tiny pick-and-placeable vision sensor that is perfect for your next AI or robotics - or AI robotics - product! With the global shutter, you'll be able to get clear and complete photos each time, no matter your lighting and subject speed. We stock low-cost simple camera sensors like the OV5640 at the Adafruit shop (https://www.adafruit.com/product/5839) these cameras can do color, up to 720p or greater, and can even do internal JPEG compression before piping the image out of an 8-bit parallel interface. One thing that you'll quickly realized about these cameras is that they, like almost all cameras used for basic photography are rolling-shutter type. (https://en.wikipedia.org/wiki/Rolling_shutter) That means the sensor reads each individual pixel in a row before moving to the next column, perfectly fine as long as the thing you're photographing is moving slowly compared to the speed of the sensor iterator. For robotics vision projects, this often gives smeared or blurry images, and since time = money and thus you need to run the motor as fast as possible. For example, our SM481 pick and place (https://www.hanwha-pm.com/en-mo/product/detail.asp?product_info_id=189&cate_id=50) can do up to 40,000 components per hour, each one with vision inspection: that's 10 a second! Whether you are building the fastest Rubik's-cube solver (https://www.youtube.com/watch?v=59qgzzSD1tk) or a license plate reader (https://www.digikey.com/short/45p5vfvr) getting crisp-clear full-frame images is essential to make sure you get the best image. The ARX383CS (https://www.digikey.com/short/45p5vfvr) is sold as a chip-scale-package, meant for pick and placing directly onto a PCB or FPC. It'll need various power supplies and clock signal, as well as configuration over I2C and of course a lens and lighting. Once set up, images can be captured and sent over DSI/MIPI single-lane, at VGA 640x480 up to 120 FPS or quarter-VGA 320x240 up to 245 FPS. The available datasheet doesn't have all the details, you'll need to contact onsemi to sign an NDA for the full specifications. onsemi has also developed a read-to-go plug-in camera module that you can quickly integrate called the PRISM1M-ARX383CSSM130110-GEVB (https://www.onsemi.com/design/evaluation-board/PRISM1M-ARX383CSSM130110-GEVB) which is not in stock right now at DigiKey yet (https://www.digikey.com/short/zfm5d7tj) but we're sure that if you need it you can try contacting DigiKey's sales reps and they'll be able to get you samples and quantity pricing. If you don't mind a bulkier eval board, the ARX383CSSM28SMKAH3-GEVB (https://www.digikey.com/short/78p2c3dq) is available immediately for purchase. If you've needed to add fast video or photography to your next product, the onsemi ARX383CS 1/8-inch 0.3 Mp Global Shutter CMOS Digital Image Sensor (https://www.digikey.com/short/45p5vfvr) is an excellent way to add a VGA global-shutter sensor with 125 FPS VGA-resolution output and I2C control. Best of all DigiKey has tons in stock for immediate shipment, book today and they'll send you as many as you want in the blink of an eye so you can start getting high speed video integrated by tomorrow afternoon. See the onseemi video here https://www.youtube.com/watch?v=Ne8O8NlyIas

The hush-hush news from Adafruit in Industry City, Brooklyn, New York. Broadcast May 21, 2025 These are items or concept products that may/might/could be introduced into the Adafruit store in the future (or not)! It's not out yet, so please don't ask questions or ask when it'll be available.... Check out the Adafruit store for all the great products that are available and for coming soon products you can sign up to be notified when they are in stock. https://www.adafruit.com/new Visit the Adafruit shop online - http://www.adafruit.com Also visit DigiKey for Adafruit products at http://www.digikey.com/ ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/

Build a 2-axis motorized camera slider using smooth silent stepper motors and Adafruit KB2040 running Circuit Python. Learn Guide: https://learn.adafruit.com/motorized-camera-slider-2-axis TMC2209 Driver: https://www.adafruit.com/product/6121 KBRP2040 Board: https://www.adafruit.com/product/5302 1.3in TFT Display: https://www.adafruit.com/product/4313 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Full tutorial: https://learn.adafruit.com/glowing-birthday-number-crown/overview Make a necklace or tiara for your favorite birthday girl that proudly displays her age in shining lights. This beginner-friendly guide walks you through building a magical LED tiara or necklace that displays the birthday child's age using Adafruit's flexible LED number filaments. These filaments run at 3V and are powered by coin cell batteries—one battery per number—making the design lightweight, wearable, and delightfully low-tech. This project requires a little easy soldering and no coding, and you'll end up with a sturdy, eye-catching crown that's safe for kids and perfect for birthdays, dress-up days, and royal make-believe adventures.  Visit the Adafruit shop online - http://www.adafruit.com Erin St Blaine - www.erinstblaine.com Music by SUNO AI ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Every week we'll 3D print designs from the community and showcase slicer settings, use cases and of course, Time-lapses! This Week: Tic-Tac-Toe Keychain By Nova.E makerworld.com/en/models/1425094-a-portable-tic-tac-toe-keychain-that-doesn-t-requi Bambu X1C Blue White Yellow Red PLA 3hr 47mins X:60 Y:60 Z:12mm .2mm layer / .4mm Nozzle 6% Infill / 1mm Retraction 200C / 60C 30g 230mm/s ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Shop for parts to build your own DIY projects http://adafru.it/3dprinting 3D Printing Projects Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOWD2dJNRIN46uhMCWvNOlbG 3D Hangout Show Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVgpmWevin2slopw_A3-A8Y Layer by Layer CAD Tutorials Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVsMp6nKnpjsXSQ45nxfORb Timelapse Tuesday Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVagy3CktXsAAs4b153xpp_ Connect with Noe and Pedro on Social Media: Noe's Twitter / Instagram: @ecken Pedro's Twitter / Instagram: @videopixil ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Subscribe to Adafruit on YouTube: http://adafru.it/subscribe Adafruit Monthly Deals & FREE Specials https://www.adafruit.com/free?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Join our weekly Show & Tell on G+ Hangouts On Air: http://adafru.it/showtell Watch our latest project videos: http://adafru.it/latest?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting 3DThursday Posts: https://blog.adafruit.com/category/3d-printing?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting New tutorials on the Adafruit Learning System: http://learn.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Music by Dan Q https://soundcloud.com/adafruit -----------------------------------------

0:00 Housekeeping 2:30 Community News 5:32 State of CircuitPython, Libraries & Blinka 11:37 Hug Reports 14:20 Status Updates 20:38 In the Weeds 20:50 Wrap-up Notes document is available here, with timecodes: https://github.com/adafruit/adafruit-circuitpython-weekly-meeting/blob/main/2025/2025-05-19.md Join here for the chat all week: http://adafru.it/discord The CircuitPython Weekly normally is held at 2pm US ET/11am us PT on Mondays. Check the #circuitpython-dev channel on Discord for notices of change in time and links to past meetings. Meeting times are also available in iCal format using the following link: https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical or view it in your browser: https://open-web-calendar.herokuapp.com/calendar.html?url=https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical CircuitPython development is sponsored by Adafruit. Please support them by purchasing hardware from https://adafruit.com. Reminders: Podcast available on most services. Let us know if we're missing some. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

For the ACS37800 breakout, we need chunky terminal blocks for high-current circuits. Since the chip can handle 30 Amps, we're going with compact barrier blocks so users can safely connect spade/lug terminals without shorts. Here's our pick at digikey.com: https://www.digikey.com/en/products/detail/amphenol-anytek/YK4410303000G/4961614 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Larsio Paint Music is an homage to Mario Paint music composition mode running on Metro RP2350 and the upcoming Fruit Jam board. Written in CircuitPython, John Park's Learn Guide coming soon. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

John Park's Workshop Live 5/15/25 Sparkle Toes 2: Electric Shoegaloo CircuitPython Parsec JPPPoW recap Projects and more! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Adafruit SEN6x Breakout for Sensirion SEN66 - STEMMA QT / Qwiic (0:31) https://www.adafruit.com/product/6331 Adafruit Sparkle Motion Stick + Enclosure Kit (1:28) https://www.adafruit.com/product/6333 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- New nEw NEWs New Products, News, and more: https://www.adafruit.com/newsletter #newnewnew Shop for all of the newest Adafruit products: http://adafru.it/new Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

This week's EYE ON NPI is a follow up to one we did a few years ago on the similarly-named BQ25792 (https://blog.adafruit.com/2021/05/06/eye-on-npi-ti-bq25792-i2c-controlled-1-4-cell-5a-buck-boost-battery-charger-eyeonnpi-adafruit-digikey-adafruit-digikey-txinstruments/). The BQ25798 (https://www.digikey.com/short/vnr279pz) builds on the '92 by adding selectable dual inputs and true MPPT solar support. This chip is inexpensive, powerful and can handle almost any battery and power source matching you desire. Let's look at some specifications: High power density, high integration buck-boost charger for 1-4 cell batteries supporting USB PD 3.0 profile – Integrates four switching MOSFETs, BATFET – Integrates input and charging current sensing Highly efficient – 750-kHz or 1.5-MHz switching frequencies – 5-A charging current with 10-mA resolution 96.5% efficient: 16-V battery at 3A from 20V Supports a wide range of input sources Autonomously sampled open circuit voltage (VOC) maximum power point tracking (MPPT) for charging from a photovoltaic panel – 3.6-V to 24-V wide input operating voltage range with 30-V absolute maximum rating – Detects USB BC1.2, HVDCP and non-standard adapters Dual-input power mux controller (optional) Narrow voltage DC (NVDC) power path Backup Mode with Ultra-fast switchover to adjustable voltage Powers USB port from battery (USB OTG) – 2.8-V to 22-V OTG output voltage with 10-mV resolution to support USB-PD PPS – OTG output current regulation up to 3.32 A with 40-mA resolution Flexible autonomous and I2C mode for optimal system performance Integrated 16-bit ADC for voltage, current, and temperature monitoring Like the '92, the BQ25798 (https://www.digikey.com/short/vnr279pz) supports any size battery. We have lots of battery packs in the Adafruit shop, and in particular we use 1S batteries – if there are more batteries, they are wired in series. But there's lot of folks who are building robotics that require higher voltages, so they have 2S, 3S, or 4S batteries. This charger can handle any of 'em, and you can configure the battery pack size using a simple resistor on the PROG port. In this case it also allows the chip to run in 'standalone' mode without the use of I2C to configure. The biggest improvement you get with the BQ25798 (https://www.digikey.com/short/vnr279pz) is true solar MPPT support. The BQ25792 had VINDPM and IINDPM – the ability to track the input voltage to make sure it is not drooping from overdraw. While this lets you get pretty-close-to-MPPT it isn't true power-point-tracking which requires perturbation around the voltage to adjust as light and temperature affect the solar panel's efficiency. The '98 does this 'right' and even has a K Factor adjustment register - you can tweak this to get the best results based on different weather/temperature (https://www.ti.com/video/6287049638001)- or stick to the default value for good results. Another new feature is 'selectable dual-inputs' what this means if you can set up two power inputs - say DC plug and Solar - and then have the chip switch between them. This is particularly useful because you can't just use two OR'ing diodes to select the power source: the solar panel might have a higher initial open-voltage but can't supply as much current as a DC plug. I2C lets you select which one is priority! The BQ25798 (https://www.digikey.com/short/vnr279pz) also has many of the cool features we liked in the BQ25792: On-The-Go mode where you can turn the buck-boost around and have it generate a variable voltage output, say 5V for powering other USB devices. Another thing that works is powering over USB where you can have the BQ negotiate 'high voltage' support from USB 3 ports. Note that this isn't USB Type C power negotiation, for that you'll want to get a separate USB Type C PD negotiation chip like the TPS25750D (https://www.tij.co.jp/jp/lit/ml/slpp103/slpp103.pdf)...we're hoping there's a future version with PD built in! There's also a built in 16-bit ADC that you can use to monitor various voltages and current draw. While you can charge the battery in 'standalone' mode - you really do need I2C to get the best performance and capabilities. Thankfully there's not a huge number of registers, and SDA/SCL can be 3 or 5V logic signals so you should be able to get it working on anything from an ATmega328 to a Raspberry Pi. We like the high integration: you really only need a few passives and an inductor to get a fantastic all-in-one charger for any lithium ion battery pack. If you're intrigued and would like more information, you've come to the right place! DigiKey has the BQ25798 (https://www.digikey.com/short/vnr279pz) in stock right now for immediate shipment. Order today and you can start designing your solar-powered products of the future by tomorrow afternoon.

Join Ladyada as she breaks down how recent tariff shifts impact electronic component availability and pricing, reshoring trends, and what may happen to engineering/BOM and DIY project costs. Get the inside scoop on navigating supply chain challenges while keeping your builds affordable and excellent! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #tariffs #usa #manufacturing

ASK AN ENGINEER 5/14/2025 LIVE! Tariff Talk! @05:44 From the Desk of Ladyada @13:54 JP's Product Pick of the Week @15:04 Open Source Hardware @16:44 3D Printing @22:34 Eye on NPI @24:30 New Products @36:43 Top Secret @41:42 Questions @47:12 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

ASK AN ENGINEER 5/14/2025 LIVE! Tariff Talk! @05:44 From the Desk of Ladyada @13:54 JP's Product Pick of the Week @15:04 Open Source Hardware @16:44 3D Printing @22:34 Eye on NPI @24:30 New Products @36:43 Top Secret @41:42 Questions @47:12 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

#newproducts JP's Product Pick of the Week 5/13/25 RECAP PiCowbell Adalogger https://www.adafruit.com/product/5703 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

We're wrapping up the design for the OPT4048 breakout: mostly putting the finishing touches on the Arduino library (https://github.com/adafruit/Adafruit_OPT4048). Since the whole point of this sensor is that it gives you CIE X & Y coordinates, we thought it would be cool to plot that onto a CIE diagram (https://en.wikipedia.org/wiki/CIE_1931_color_space). Historically, we'd have to use Processing (https://processing.org/), but now you can use WebSerial to get data directly from a microcontroller! Only catch — it's been like 15 years since I wrote JavaScript, so we asked Claude Code (https://docs.anthropic.com/en/docs/claude-code/overview) to help out. With a little direction, it delivered a perfect demo (https://github.com/adafruit/Adafruit_OPT4048/commits/gh-pages) in about 30 minutes. It was so fun, we're thinking of doing WebSerial demos for more products! You can try it out by uploading the code here (https://github.com/adafruit/Adafruit_OPT4048/blob/main/examples/opt4048_webserial/opt4048_webserial.ino) and then visiting this page: https://adafruit.github.io/Adafruit_OPT4048/webserial/ #Arduino #WebSerial #ColorSensor Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Full tutorial: https://learn.adafruit.com/butterfly-bench-with-edge-lit-acrylic/overview Build a bench for your backyard or your festival theme camp that shows your logo or camp mascot in glowing rainbow colors. Playa Tech is a system of furniture plans designed by Sunshine Zwern. Create benches, tables and chairs from a single sheet of plywood using common wood shop tools. The furniture packs flat, then slots together in minutes, allowing you to bring an entire living room set for your festival camp in the back of your Subaru. This system is rapidly gaining popularity with the Burning Man crowd, and we've seen it being used at festivals nationwide. Our camp decided to get a bit fancy this year and worked together to create this Playa Tech Butterfly Bench. The butterfly is cut with a handheld CNC router from a sheet of 3/4" plywood, and then back-lit with edge-lit 1/4" acrylic, 30/m NeoPixels and running WLED software powered by a Sparkle Motion board. It's a lovely addition to our camp setup, and makes an absolutely lovely "selfie spot" in any garden. The LED build is pretty easy on this project. The challenge is in the woodworking. But, who doesn't love a good woodworking challenge? Visit the Adafruit shop online - http://www.adafruit.com Erin St Blaine - http://www.erinstblaine.com Playa Tech Furniture - http://www.playatech.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

#newproducts JP's Product Pick of the Week 5/13/25 PiCowbell Adalogger https://www.adafruit.com/product/5703 Deep discount during livestream Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Every week we'll 3D print designs from the community and showcase slicer settings, use cases and of course, Time-lapses! This Week: Cardboard Crafting Tools By ValeriaMomo https://cults3d.com/:2944214 Bambu X1C Blue Grey Yellow PLA 4hr 36mins X:108 Y:123 Z:74mm .2mm layer / .4mm Nozzle 6% Infill / 1mm Retraction 200C / 60C 77g 230mm/s ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Shop for parts to build your own DIY projects http://adafru.it/3dprinting 3D Printing Projects Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOWD2dJNRIN46uhMCWvNOlbG 3D Hangout Show Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVgpmWevin2slopw_A3-A8Y Layer by Layer CAD Tutorials Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVsMp6nKnpjsXSQ45nxfORb Timelapse Tuesday Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVagy3CktXsAAs4b153xpp_ Connect with Noe and Pedro on Social Media: Noe's Twitter / Instagram: @ecken Pedro's Twitter / Instagram: @videopixil ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Subscribe to Adafruit on YouTube: http://adafru.it/subscribe Adafruit Monthly Deals & FREE Specials https://www.adafruit.com/free?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Join our weekly Show & Tell on G+ Hangouts On Air: http://adafru.it/showtell Watch our latest project videos: http://adafru.it/latest?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting 3DThursday Posts: https://blog.adafruit.com/category/3d-printing?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting New tutorials on the Adafruit Learning System: http://learn.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Music by Dan Q https://soundcloud.com/adafruit -----------------------------------------

We're phasing out the Cirrus WM8960 codec (https://www.digikey.com/en/products/detail/cirrus-logic-inc/WM8960CGEFL-V/5036712) used in some Raspberry Pi boards to add two microphones, line-out, and stereo speaker. The codec is great—see our Voice Bonnet—but very obsolete now. Let's hunt for a modern alternative! See the chosen part on DigiKey https://www.digikey.com/short/3jnw089v Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Notes document is available here, with timecodes: https://github.com/adafruit/adafruit-circuitpython-weekly-meeting/blob/main/2025/2025-05-12.md 0:00 Housekeeping 04:03 Community News 08:47 State of CircuitPython, Libraries & Blinka 20:49 Hug Reports 23:22 Status Updates 26:51 In the Weeds 27:09 Wrap-up Join here for the chat all week: http://adafru.it/discord The CircuitPython Weekly normally is held at 2pm US ET/11am us PT on Mondays. Check the #circuitpython-dev channel on Discord for notices of change in time and links to past meetings. Meeting times are also available in iCal format using the following link: https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical or view it in your browser: https://open-web-calendar.herokuapp.com/calendar.html?url=https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical CircuitPython development is sponsored by Adafruit. Please support them by purchasing hardware from https://adafruit.com. Reminders: Podcast available on most services. Let us know if we're missing some. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

We found an old Advanced Circuits panel and we started chatting—DIGG is back! (https://reboot.digg.com/) What if we remade the DIGG button kit with a WiFi chip to show your live vote count? Let's revive this classic, starting with the 3-digit 7-segment display. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Raspberry Pi Pico 2 with Header https://www.adafruit.com/product/6328 ----------------------------------------- New nEw NEWs New Products, News, and more: https://www.adafruit.com/newsletter #newnewnew Shop for all of the newest Adafruit products: http://adafru.it/new Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

John Park's Workshop Live 5/8/25 CircuitPython Parsec JPPPoW recap Projects and more! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

#circuitpythonparsec How to read button bitmasks from seesaw boards such as the Gamepad QT. https://github.com/jedgarpark/parsec/blob/main/2025-05-01/code.py https://www.adafruit.com/product/5743 Learn about CircuitPython: https://circuitpython.org Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Raspberry Pi Pico 2 with Header https://www.adafruit.com/product/6328 ----------------------------------------- New nEw NEWs New Products, News, and more: https://www.adafruit.com/newsletter #newnewnew Shop for all of the newest Adafruit products: http://adafru.it/new Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

ASK AN ENGINEER 5/7/2025 LIVE Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #diy #electronics #manufacturing

The wonderful world of Python on hardware! Episode 310 (May 7, 2025). This is our weekly Python video highlights! Ladyada and PT review the Python on hardware news of the week. The news comes from the Python community, Discord, Adafruit communities and more. It's part of the comprehensive newsletter we do each week. The video playlist of episodes is here: http://adafru.it/pohepisodes *************************************************** Sign up for the Python on Microcontrollers weekly email newsletter here: https://www.adafruitdaily.com/ Over 12,168 subscribers! *************************************************** Read the newsletters past and present at https://www.adafruitdaily.com/category/circuitpython/ Learn all about CircuitPython here: https://www.circuitpython.org/ https://adafruit.com/circuitpython/ Over 600 compatible microcontroller boards! --------------------------------------------------------------- Join us on Discord! https://adafru.it/discord/ Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe

The hush-hush news from Adafruit in Industry City, Brooklyn, New York. Broadcast May 7, 2025 These are items or concept products that may/might/could be introduced into the Adafruit store in the future (or not)! It's not out yet, so please don't ask questions or ask when it'll be available.... Check out the Adafruit store for all the great products that are available and for coming soon products you can sign up to be notified when they are in stock. https://www.adafruit.com/new Visit the Adafruit shop online - http://www.adafruit.com Also visit DigiKey for Adafruit products at http://www.digikey.com/ ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/

Join Ladyada as she breaks down how recent tariff shifts impact electronic component availability and pricing, reshoring trends, and what may happen to engineering/BOM and DIY project costs. Get the inside scoop on navigating supply chain challenges while keeping your builds affordable and excellent! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #tariffs #usa #manufacturing

This week's EYE ON NPI features a new 'everything' sensor, the Sensirion SEN66 Environmental Sensor Node (https://www.digikey.com/en/product-highlight/s/sensirion/environmental-sensor-node-sen6x) . This is a highly-anticipated update to the SEN5x (https://www.digikey.com/en/videos/s/sensirion/eye-on-npi-sen54-environmental-sensor-node) goes hard on gas sensing, with VOC, NOx and CO2 sensors built in. You can even update to the SEN68 and get formaldehyde HCHO sensing! What we like about this series is the complete solution for all kinds of environmental sensing with a single cable. Sensirion is one of our fav sensor companies: from classics like the SHT45 (https://www.adafruit.com/product/5665) to the popular SGP30 (https://www.adafruit.com/product/3709) and the high quality SCD30 (https://www.adafruit.com/product/4867) we have made breakouts for many-a-sensor from this company. Lately they've started to do fully integrated products - like the SEN5x series (https://www.digikey.com/en/videos/s/sensirion/eye-on-npi-sen54-environmental-sensor-node) that we covered earlier on EYE ON NPI. The SEN54 series has particulate matter (PM1, PM2.5, PM4, PM10) dust sensing, plus temperature, humidity, volatile organic compounds (VOCs), with the SEN55 adding NOx. We saw this sensor often paired with an SCD30 (https://www.digikey.com/short/d1h3t1n4) or SCD4x (https://www.digikey.com/short/zmh2zjz3) to add CO2 sensing. Those folks will like the look of the SEN6x series as now we get CO2 sensing in all but the lowest-cost SEN60. One thing to note with CO2 sensing is that once a week it needs to 'self-calibrated' by letting it sense fresh outdoor air which will be ~400ppm. This isn't a bad idea for your health either. Another new sensor added in the upcoming SEN68 is formaldehyde, which integrates the SFA30 (https://www.digikey.com/short/2d5fb8rt). If you've used the SEN5x series, (https://www.digikey.com/en/videos/s/sensirion/eye-on-npi-sen54-environmental-sensor-node) you're probably familiar with their connection interface: a JST GH 6-pin cable is used to connect and provide power and I2C data connection. However, one thing to note is that the cable is the same but the pinout has changed. Power is now 3.3V instead of 5.0 and there's no UART interface, so the SEL pin is not available. For that reason, if you'd like to use the same cable, go for it - but the circuitry will need to change...for example we're revising our SEN5x breakout (https://www.digikey.com/short/h0jffnm2)! We like that, just as with the SEN5x series, the SEN6x (https://www.digikey.com/en/product-highlight/s/sensirion/environmental-sensor-node-sen6x) uses plain I2C to communicate. This makes it easy to integrate with any microcontroller or microcomputer, and the added CRC helps avoid accidental data corruption from EMI or loose cables. The interface is not just to each individual sensor - there's only one I2C address and command structure and once you initialize the sensor you can read all values at once for 'timestamped' consistency. The commands are easy to implement, but if you want a head-start, check out the Sensirion GitHub account (https://github.com/Sensirion?q=sen6&type=all&language=&sort=), they have code in C and Python for a 5-minute quick start. Excited to check this fancy new combo-sensor out? You're in luck because DigiKey has the Sensirion SEN66 Environmental Sensor Node (https://www.digikey.com/short/0d4jt424) in stock right now for immediate shipment! Order today and DigiKey will ship it you in an instant - you will be sensing up a storm by tomorrow afternoon! See at DigiKey https://www.digikey.com/short/0d4jt424 See Sensiron's video https://www.digikey.com/api/videos/videoplayer/smallplayer/6371044300112 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

ASK AN ENGINEER 5/7/2025 LIVE Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #diy #electronics #manufacturing

#newproducts JP's Product Pick of the Week 5/6/25 PiCowbell Camera Breakout https://www.adafruit.com/product/5946 Deep discount during livestream Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

#newproducts JP's Product Pick of the Week 5/6/25 PiCowbell Camera Breakout https://www.adafruit.com/product/5946 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Every week we'll 3D print designs from the community and showcase slicer settings, use cases and of course, Time-lapses! This Week: Mailbox for Children By BamBam Design printables.com/model/1026728-mailbox-for-children/files Bambu X1C Gold Red PLA 25hr 15mins X:191 Y:220 Z:30mm .2mm layer / .4mm Nozzle 6% Infill / 1mm Retraction 200C / 60C 188g 230mm/s Flag Design by VikingLanding : https://www.thingiverse.com/thing:3995684 ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Shop for parts to build your own DIY projects http://adafru.it/3dprinting 3D Printing Projects Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOWD2dJNRIN46uhMCWvNOlbG 3D Hangout Show Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVgpmWevin2slopw_A3-A8Y Layer by Layer CAD Tutorials Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVsMp6nKnpjsXSQ45nxfORb Timelapse Tuesday Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVagy3CktXsAAs4b153xpp_ Connect with Noe and Pedro on Social Media: Noe's Twitter / Instagram: @ecken Pedro's Twitter / Instagram: @videopixil ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Subscribe to Adafruit on YouTube: http://adafru.it/subscribe Adafruit Monthly Deals & FREE Specials https://www.adafruit.com/free?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Join our weekly Show & Tell on G+ Hangouts On Air: http://adafru.it/showtell Watch our latest project videos: http://adafru.it/latest?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting 3DThursday Posts: https://blog.adafruit.com/category/3d-printing?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting New tutorials on the Adafruit Learning System: http://learn.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Music by Dan Q https://soundcloud.com/adafruit -----------------------------------------

For our solar-capable Feathers, we're going to design a FeatherWing helper board to assist with solar connection and monitoring. To do that, we will want to monitor two voltages (the LiPoly battery and the solar panel) and one current (the panel draw). Traditionally, we've liked using the INA219 and friends—let's see if we can find a voltage/current monitor chip with an I2C interface and at least two monitoring inputs. See the part on DigiKey https://www.digikey.com/short/tmc77hmn ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #Ladyada #FeatherWing #SolarProjects

With sunny days ahead, we're working on more solar projects. One thing that comes up often is we need is a diode to keep the PV panel current only flowing into a charging circuit. Often times folks use a Schottky diode (https://www.digikey.com/short/b5d8495f) for their low forward voltage. But as you get to an Amp or more, you're still looking at a loss of 0.5V, or 0.5W and that number only goes up with higher currents! Thus the need for an 'ideal diode': we've already got a breakout for an ideal diode but it's only 5V max (https://www.adafruit.com/product/5830). Let's look for one that can handle higher voltages and at least an Amp of current. See the part on Digikey https://www.digikey.com/short/vj2jzpj8 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Notes document is available here, with timecodes: https://github.com/adafruit/adafruit-circuitpython-weekly-meeting/blob/main/2025/2025-05-05.md Join here for the chat all week: http://adafru.it/discord The CircuitPython Weekly normally is held at 2pm US ET/11am us PT on Mondays. Check the #circuitpython-dev channel on Discord for notices of change in time and links to past meetings. Meeting times are also available in iCal format using the following link: https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical or view it in your browser: https://open-web-calendar.herokuapp.com/calendar.html?url=https://raw.githubusercontent.com/adafruit/adafruit-circuitpython-weekly-meeting/master/meeting.ical CircuitPython development is sponsored by Adafruit. Please support them by purchasing hardware from https://adafruit.com. Reminders: Podcast available on most services. Let us know if we're missing some. Visit the Adafruit shop online - http://www.adafruit.com 0:00 Housekeeping 02:03 Community News 04:26 State of CircuitPython, Libraries & Blinka 11:14 Hug Reports 12:58 Status Updates 19:47 Wrap-up ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

USB Type C Sync Data Cable with On-Off Switch - 1 meter long (0:05) https://www.adafruit.com/product/6269?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts USB Type C Sync Data Cable with On-Off Switch - 28cm long (0:05) https://www.adafruit.com/product/6268?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts USB Type C 3.1 PD to 5.5mm Barrel Jack Cable - 28V 5A Output - 1.8m long (2:22) https://www.adafruit.com/product/6273?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts USB C Power Monitor / Analyzer with Color TFT Graphing Display (4:10) https://www.adafruit.com/product/6272?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts Mini OLED USB C Power Analyzer (7:10) https://www.adafruit.com/product/6271?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts ----------------------------------------- New nEw NEWs New Products, News, and more: https://www.adafruit.com/newsletter #newnewnew Shop for all of the newest Adafruit products: http://adafru.it/new Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

John Park's Workshop Live 5/1/25 CircuitPython Parsec JPPPoW recap Projects and more! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

ASK AN ENGINEER 4/30/2025 LIVE Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #diy #live #electronics

The wonderful world of Python on hardware! Episode 309 (April 30, 2025). This is our weekly Python video highlights! Ladyada and PT review the Python on hardware news of the week. The news comes from the Python community, Discord, Adafruit communities and more. It's part of the comprehensive newsletter we do each week. The video playlist of episodes is here: http://adafru.it/pohepisodes *************************************************** Sign up for the Python on Microcontrollers weekly email newsletter here: https://www.adafruitdaily.com/ Over 12,144 subscribers! *************************************************** Read the newsletters past and present at https://www.adafruitdaily.com/category/circuitpython/ Learn all about CircuitPython here: https://www.circuitpython.org/ https://adafruit.com/circuitpython/ Over 600 compatible microcontroller boards! --------------------------------------------------------------- Join us on Discord! https://adafru.it/discord/ Visit the Adafruit shop online - http://www.adafruit.com Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe

The hush-hush news from Adafruit in Industry City, Brooklyn, New York. Broadcast April 30, 2025 These are items or concept products that may/might/could be introduced into the Adafruit store in the future (or not)! It's not out yet, so please don't ask questions or ask when it'll be available.... Check out the Adafruit store for all the great products that are available and for coming soon products you can sign up to be notified when they are in stock. https://www.adafruit.com/new Visit the Adafruit shop online - http://www.adafruit.com Also visit DigiKey for Adafruit products at http://www.digikey.com/ ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/

Join Ladyada as she breaks down how recent tariff shifts impact electronic component availability and pricing, reshoring trends, and what may happen to engineering/BOM and DIY project costs. Get the inside scoop on navigating supply chain challenges while keeping your builds affordable and excellent! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #tariffs #usa #manufacturing

#newproducts JP's Product Pick of the Week 4/29/25 TLV320DAC3100 I2S DAC w Headphone and Speaker Outs https://www.adafruit.com/product/6309 Deep discount during livestream Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------

Over the holiday break, we designed a few Sparkle Motion (https://www.adafruit.com/search?q=sparkle+motion) ESP32 boards for use with WLED. They've been working well, so we decided to finish up the third version we cooked up—a USB “stick” for quick builds that you can power from a wall adapter, computer, or even a USB battery pack for portability. We managed to fit in a fuse, an I²S microphone, infrared-remote input, a mode-select button, two level-shifted outputs, and terminal blocks. It's designed to fit inside a pre-made snap-fit case (https://www.adafruit.com/product/6176). Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #esp32 #wled #diy

Build a Piranha Plant themed camera using a Raspberry Pi 5! Guide: https://learn.adafruit.com/piranha-pi-cam The Warp Pipe-shaped base houses the Pi 5 with a fan and a 4" touch screen. A camera module is housed inside the Piranha mouth. The case has access to the USB ports with vents on the side to keep the Pi cool. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Shop for parts to build your own DIY projects http://adafru.it/3dprinting 3D Printing Projects Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOWD2dJNRIN46uhMCWvNOlbG 3D Hangout Show Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVgpmWevin2slopw_A3-A8Y Layer by Layer CAD Tutorials Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVsMp6nKnpjsXSQ45nxfORb Timelapse Tuesday Playlist: https://www.youtube.com/playlist?list=PLjF7R1fz_OOVagy3CktXsAAs4b153xpp_ Connect with Noe and Pedro on Social Media: Noe's Twitter / Instagram: @ecken Pedro's Twitter / Instagram: @videopixil ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Subscribe to Adafruit on YouTube: http://adafru.it/subscribe Adafruit Monthly Deals & FREE Specials https://www.adafruit.com/free?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Join our weekly Show & Tell on G+ Hangouts On Air: http://adafru.it/showtell Watch our latest project videos: http://adafru.it/latest?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting 3DThursday Posts: https://blog.adafruit.com/category/3d-printing?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting New tutorials on the Adafruit Learning System: http://learn.adafruit.com/?utm_source=youtube&utm_medium=videodescrip&utm_campaign=3dprinting Music by Dan Q https://soundcloud.com/adafruit -----------------------------------------