POPULARITY
This week's EYE ON NPI is a follow up to one we did a few years ago on the similarly-named BQ25792 (https://blog.adafruit.com/2021/05/06/eye-on-npi-ti-bq25792-i2c-controlled-1-4-cell-5a-buck-boost-battery-charger-eyeonnpi-adafruit-digikey-adafruit-digikey-txinstruments/). The BQ25798 (https://www.digikey.com/short/vnr279pz) builds on the '92 by adding selectable dual inputs and true MPPT solar support. This chip is inexpensive, powerful and can handle almost any battery and power source matching you desire. Let's look at some specifications: High power density, high integration buck-boost charger for 1-4 cell batteries supporting USB PD 3.0 profile – Integrates four switching MOSFETs, BATFET – Integrates input and charging current sensing Highly efficient – 750-kHz or 1.5-MHz switching frequencies – 5-A charging current with 10-mA resolution 96.5% efficient: 16-V battery at 3A from 20V Supports a wide range of input sources Autonomously sampled open circuit voltage (VOC) maximum power point tracking (MPPT) for charging from a photovoltaic panel – 3.6-V to 24-V wide input operating voltage range with 30-V absolute maximum rating – Detects USB BC1.2, HVDCP and non-standard adapters Dual-input power mux controller (optional) Narrow voltage DC (NVDC) power path Backup Mode with Ultra-fast switchover to adjustable voltage Powers USB port from battery (USB OTG) – 2.8-V to 22-V OTG output voltage with 10-mV resolution to support USB-PD PPS – OTG output current regulation up to 3.32 A with 40-mA resolution Flexible autonomous and I2C mode for optimal system performance Integrated 16-bit ADC for voltage, current, and temperature monitoring Like the '92, the BQ25798 (https://www.digikey.com/short/vnr279pz) supports any size battery. We have lots of battery packs in the Adafruit shop, and in particular we use 1S batteries – if there are more batteries, they are wired in series. But there's lot of folks who are building robotics that require higher voltages, so they have 2S, 3S, or 4S batteries. This charger can handle any of 'em, and you can configure the battery pack size using a simple resistor on the PROG port. In this case it also allows the chip to run in 'standalone' mode without the use of I2C to configure. The biggest improvement you get with the BQ25798 (https://www.digikey.com/short/vnr279pz) is true solar MPPT support. The BQ25792 had VINDPM and IINDPM – the ability to track the input voltage to make sure it is not drooping from overdraw. While this lets you get pretty-close-to-MPPT it isn't true power-point-tracking which requires perturbation around the voltage to adjust as light and temperature affect the solar panel's efficiency. The '98 does this 'right' and even has a K Factor adjustment register - you can tweak this to get the best results based on different weather/temperature (https://www.ti.com/video/6287049638001)- or stick to the default value for good results. Another new feature is 'selectable dual-inputs' what this means if you can set up two power inputs - say DC plug and Solar - and then have the chip switch between them. This is particularly useful because you can't just use two OR'ing diodes to select the power source: the solar panel might have a higher initial open-voltage but can't supply as much current as a DC plug. I2C lets you select which one is priority! The BQ25798 (https://www.digikey.com/short/vnr279pz) also has many of the cool features we liked in the BQ25792: On-The-Go mode where you can turn the buck-boost around and have it generate a variable voltage output, say 5V for powering other USB devices. Another thing that works is powering over USB where you can have the BQ negotiate 'high voltage' support from USB 3 ports. Note that this isn't USB Type C power negotiation, for that you'll want to get a separate USB Type C PD negotiation chip like the TPS25750D (https://www.tij.co.jp/jp/lit/ml/slpp103/slpp103.pdf)...we're hoping there's a future version with PD built in! There's also a built in 16-bit ADC that you can use to monitor various voltages and current draw. While you can charge the battery in 'standalone' mode - you really do need I2C to get the best performance and capabilities. Thankfully there's not a huge number of registers, and SDA/SCL can be 3 or 5V logic signals so you should be able to get it working on anything from an ATmega328 to a Raspberry Pi. We like the high integration: you really only need a few passives and an inductor to get a fantastic all-in-one charger for any lithium ion battery pack. If you're intrigued and would like more information, you've come to the right place! DigiKey has the BQ25798 (https://www.digikey.com/short/vnr279pz) in stock right now for immediate shipment. Order today and you can start designing your solar-powered products of the future by tomorrow afternoon.
On this week's show we look at a technology that could end HDMI. We also read your emails and take a look at the week's news. News: Sony steps away from 8K TVs – for now Survey: Share of Homes With TV Antennas Falls to 19% DIRECTV unites streaming options under one name and price structure Peacock highlights cool features for mobile users Other: AUBESS Tuya WiFi 16A Mini Smart Switch Is GPMI the beginning of the end of HDMI? Over 50 Chinese companies including Hisense and TCL have joined forces to back an HDMI alternative called GPMI (General Purpose Media Interface). This new wired communication standard is designed to integrate multiple functionalities into a single cable, aiming to rival HDMI, DisplayPort, and Thunderbolt. The following are some key features: High Bandwidth for Data Transmission - GPMI Type-B: Supports up to 192 Gbps bandwidth, significantly surpassing HDMI 2.1 (48 Gbps), HDMI 2.2 (96 Gbps), DisplayPort 2.1 (80 Gbps), and Thunderbolt 4 (40 Gbps). GPMI Type-C: Offers up to 96 Gbps, compatible with USB-C ports, doubling the 40 Gbps limit of USB4 with Extended Power Range (EPR) under USB PD 3.1. Enables ultra-high-definition video - including 8K at 120Hz or higher, suitable for next-generation displays, gaming, and professional applications. Power Delivery GPMI Type-B: Delivers up to 480W of power, far exceeding Thunderbolt 4 (100W) and USB4 (240W with EPR). GPMI Type-C: Provides up to 240W, matching USB4 EPR capabilities. This eliminates the need for separate power cables - simplifying setups for devices like TVs, monitors, and gaming laptops. All-in-One Cable Solution - Combines video, audio, data transfer, network connectivity, and power delivery into a single cable, reducing cable clutter. Supports bidirectional data transfer - allowing devices to send and receive data simultaneously. Compatibility and Connectivity - GPMI Type-C: Licensed by the USB Implementers Forum ensuring compatibility with existing USB-C ecosystems for smartphones, PCs, and TVs. GPMI Type-B: Uses a proprietary connector, which may face adoption challenges unless widely licensed. Backward-compatible with USB-C and DisplayPort standards - easing transitions without requiring immediate hardware replacements. Universal Control and Device Management - Supports a universal control standard similar to HDMI-CEC, allowing a single remote to control multiple GPMI-connected devices Security Features - Integrates the ADCP (Advanced Digital Content Protection) protocol for secure content transmission. Supports daisy-chaining - similar to DisplayPort, for connecting multiple devices in series. Limitations and Notes While GPMI supports 8K video, HDMI 2.1 and DisplayPort 2.1 can handle higher resolutions (10K and 16K, respectively), though without power delivery. Adoption is currently limited to Chinese companies (e.g., Huawei, Hisense, TCL), and global traction depends on integration into mainstream devices and compatibility with non-Chinese brands like Sony, Intel, or NVIDIA. The proprietary Type-B connector may face adoption hurdles compared to the USB-C-based Type-C variant. Commercialization is planned for Q1 2025, with consumer products expected by early 2026. GPMI's combination of high bandwidth, power delivery, and multifunctionality positions it as a potential game-changer, particularly for 8K content and simplified connectivity, though its success hinges on widespread adoption and global market acceptance.
Here's the Supporter-only Q&A from January 2nd, 2025. All comments and questions are fielded through the supporter service Q&A page. Please consider supporting this channel via monthly support services, tips, or even just by using our affiliate links to purchase things you were already going to buy anyway, at no extra cost to you: https://www.retrorgb.com/support.html T-Shirts: https://retrorgb.link/tshirts Amazon Recommended List: http://retrorgb.link/amazon TIMESTAMPS (please assume all links are affiliate / paid links that pay RetroRGB a commission on each sale. Even if links are currently not affiliate, I may update them with one, should a partner list that item for sale in the future): 00:00 Welcome 00:11 Power Cord Orientation 03:01 Ramond HyperV VM's: Hyper V Windows 10 : https://mega.nz/file/zx4n3YbJ#ukqnFeA_E1gIibIGHvt0IUCHbCzInh912MYVWiefIEU Hyper V Windows 11: https://mega.nz/file/29xjGYgS#MY8D02KIH2X97lj5bYSdzJ3szX3jAg1jMjNXSKErfMU VMWare / Player 16.2: https://mega.nz/file/K5xVjCKZ#ecGI4oYi4FKKSIN4P4F0HZOznfAYZjaqeuaEKjdV6-k 03:50 Cables through a wall for a new room setup 10:37 FPGA-based IC replacements 13:50 MiSTer-based Arcade Machine 18:03 Genesis - 32x- SCD - Everdrive - Anything needed?: https://retrorgb.link/toppsu 20:53 Inline UPS as Power Conditioner: https://www.cyberpowersystems.com/blog/how-does-a-ups-work/ https://amzn.to/4gC8CYB 23:55 GameCube: https://www.retrorgb.com/flippy-drive-updates.html 24:55 LCDCRT Issues: https://github.com/MiSTer-devel/Main_MiSTer/blob/master/MiSTer.ini / https://www.retrorgb.com/scanline-filters-on-the-lcd-crt-kit.html 27:17 Why NOT to use USB-PD: https://youtube.com/live/OsuLAy2lgIk 28:31 Lumacode: https://www.retrorgb.com/ossc-lumacode-functionality-demod.html 30:27 PS2 on TINK5x…or get the CE?: https://youtu.be/LvfWZ5coqCA 33:26 Thank you!: https://www.retrorgb.com/support.html
We got the 'big' Sparkle Motion boards (https://www.adafruit.com/product/6100) out to the PCB fab house and now are turning to the mini version. This one doesn't have USB PD or 24V support, but it is very compact and has many niceties that WLED users will enjoy...like built-in ICS-43434 microphone (https://www.adafruit.com/product/6049), however during testing, we discovered that GPIO 9 and 10 were not available because the ESP32-Mini module (https://www.espressif.com/en/module/esp32-mini-1-en) we're using has slightly different pin availability! No biggie with open source firmware: we just forked and fixed and PR'd the changes here https://github.com/Aircoookie/WLED/pull/4450 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #wled #opensource #adafruit
We got our WLED-friend PCBs today, and we only made one mistake: the wrong resistor on the 3.3V feedback line. Now that it's fixed, the board seems to work great with the latest version of WLED (https://kno.wled.ge/basics/tutorials/)! we are checking all 4 signal outputs with this handy 256-LED grid that sits on our desk. Next, we will test the onboard IR receiver, USB PD, I2S microphone, extra I/O pins, and I2C. We'll also do an Arduino IDE board definition in case folks want to use it as a generic ESP32-to-LED-driver board. We're calling the board "Sparkle Motion" for now, but if you have other naming ideas, let us know - if we pick your name, you get a free board (https://www.adafruit.com/product/6100). Sign up, coming soon. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #wled #ledscreen #electronics
We got our WLED-friend PCBs (https://blog.adafruit.com/2024/12/02/leftovers-layout-wled-board-revision-a-completed/) and are testing it with various LED grids. First, we tried out a 16x16 NeoPixel grid that runs on 5V. Since that worked well, we're now onto a much bigger 60 x 60 grid - that's 3,600 LEDs! These are some NeoPixel pebble (https://www.adafruit.com/product/6024) netting samples we're also testing at the same time; each one has 20 x 60 pixels and uses 12V power, so it's a good test of the DC pass-through for higher voltages. Since WLED has a limit of 2000 pixels per output, this demo uses the three output ports that are then 'merged' together in memory to make a single large grid. We have more to test soon: the onboard IR receiver, USB PD, I2S microphone, extra I/O pins, and I2C, so watch for those videos as they come together. Coming soon - https://www.adafruit.com/product/6100 Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #wled #neopixels #ledart
We got this nifty panel-mount cable with a combo action: both USB C and DVI/HDMI connectors on both ends. This could be handy for single-board computers like Raspberry Pi's or our RP2040/RP2350 boards with DVI outputs (https://www.adafruit.com/product/5710). Since we're testing our Metro RP2350 with HSTX/DVI output anyway, this is a good time to test the cable out - some things we test with USB C cables: verify it enumerates in all 4 orientations (ya never know) and check it with a USB PD sink that requests various voltages. So far, so good; we'll get some of these into the shop in the next few weeks. Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #usb #usbc #hdmi
We're wrapping up our WLED board design (https://www.youtube.com/watch?v=M4Ybd8CdQYM) and the last part we need to spec out is the 3.3V regulator. Since we are utilizing USB PD or DC in, we could be running from 5V ~ 24VDC. For the 5V output, we only need a few mA, so we're going to pick the same LDO family we sourced earlier (https://www.youtube.com/watch?v=H_0Kua2UZCs) but for the 3.3V we need at least 500mA of current for the ESP32 chip, so a switching supply is necessary! Let's find something inexpensive with 1A+ output, 24V+ input, and we're also going to need something small so minimal passives and high frequency. See the chosen part on DigiKey https://www.digikey.com/short/rt5jw5qj ----------------------------------------- Visit the Adafruit shop online - http://www.adafruit.com LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/
Durch USB-PD (Power Delivery) laden Smartphones und Tablets deutlich schneller, ähnlich wie bei Quick Charge. Was der Unterschied ist und wie ihr eure Geräte mit bis zu 100 Watt schnellladen könnt, erklären wir euch hier.
Once in a while we find products that have center NEGATIVE DC power jacks and they really make us mad because who keeps around both positive and negative polarity versions of every voltage? now, hopefully USB PD https://www.adafruit.com/product/5807 will solve this long term, but till then this 2.1mm DC flipper flopper adapter will connect in to out and out to in and voila - your standard center-positive is now center-negative. or vice versa! how handy is that. #adafruit #cable #polarity #dcflipper Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------
Here's a podcast-style discussion on power supplies, featuring Mike Chi, Voultar and René. While this gets pretty nerdy and detailed at times, we wanted to openly discuss the issues with using aftermarket power supplies, as well as safe options for people interested. As usual, these long-form chats are available on all podcast services; Just search your favorite app for "RetroRGB Power" and you'll find it. Lots more details after the links: Quality Aftermarket PSU's: https://www.retrorgb.com/triad.htmlRetroTINK Products: https://www.retrorgb.com/retrotink.htmlVoultar's Products: https://www.voultar.com/René: https://twitter.com/WandererGuitar First, you can expect the typical banter that happens when we all get together, so expect profanity and over-the-top-silliness. That said, I think we helped clarify things for the end-user, as well as help people who might be currently working on power-related projects. And while none of us claim to know everything there is to know about power, I think the basic warnings we discussed in detail are overall excellent advice: Using bad power supplies can result in audio & video interference and in extreme cases, kill your console. PSU's that don't have CE ratings (or fake ratings) are dangerous and most people don't take power safety (and fires!) serious enough; If your house burns down as a result of using unregulated products, your insurance company could fight the payout. LOTS of clone products also clone the CE sticker. That means getting rebranded Aliexpress crap that appears to be legit could also be a fire risk. The debate between Linear vs Switch Mode PSU's is irrelevant; What's far more important is consistent performance under total load with the consoles you're connecting it to (which is why the Triads and Meanwell's are great choices). USB-PD solutions can be fine if BOTH the PSU and conversion circuit are properly built. Qwertymodo posted some great thoughts on this, but our warnings should still be taken seriously: If either end of the circuit isn't built correctly, you can send overvoltage to a console and blow out all the chips on the board. Need proof? How about the thousands of Nintendo Switch's that died as a result...from a company with a full engineering team that's been making console accessories for over twenty years: https://www.tomsguide.com/news/nintendo-switch-brick-docks ...and lastly, as we stated many times in the discussion, the goal of this was simply to educate. As with all discussions that include serious warnings, we'll be called "fearmongers" and be accused of "gatekeeping" any new products or members of the retro gaming scene. Which is extra hilarious, considering the focus of RetroRGB has always been highlighting new developers and products in the scene. Sigh, that's our punishment for trying to help... --- Support this podcast: https://podcasters.spotify.com/pod/show/retrorgb/support
We look at the new Google Pixel 8 Pro, see more on their website here. Google Pixel 8 Pro reviewed Our team were looking forward to reviewing this phone, while being curious, or even dubious about if the difference in price warranted going the extra mile to get the pro over the regular 8. Some of the differences are software divisions rather than anything specifically different in the hardware between the two devices. This debate has continued among the team for a while. One take on it was that, for those who are iPhone-ers (if that's a word) then, pricewise it is less of an issue to go for the Pro over the regular. In this case the Pixel 8 Pro is a powerful tool to have in your pocket, easily as good, if not better in some ways than anything else out there on the market. If you are in the income bracket where the pricing of the Pixel 8 Pro is not an issue, then it could be a really nice stocking filler too. The case that it came with also made the testers a little more comfortable, as it helped to negate that old issue of sleek, smooth and lethally slippy smart phones coming out of your pocket and onto hard floors at just the wrong times. As we are talking about the extra bells and whistles that the Pro brings over the regular 8, the applied AI for photography is surely market leading at this stage. Yes it might lead you to being over reliant on the idea of 'fix it in post production'. But this is also being promoted as a feature, and it does give you some freedom to capture faster, more darkly lit moments, as they happen, with great confidence that you will get an awesome image out of the experience. On the journey from reviewing Pixel 3 to Pixel 8, it has been impressive to see the growth in the quality of the photography. It is beginning to be the case that you can see clear water between the level of photographs you can capture and achieve with this phone over other competitors in the market. Our testers were very reluctant to share the phone among each other, coming up with lots of reasons why they were not quite done with it yet. Overall they were all very positive about it, and all expressed the opinion that there would be no need for tears if this popped up in their Santa stockings this year, or in any month it happened to appear. See more about the Pixel 8 Pro here DisplayFull-screen 6.7-inch (170 mm) display 20:9 aspect ratio Super Actua display (1344 x 2992) LTPO OLED at 489 PPI Smooth Display (1-120 Hz) Corning Gorilla Glass Victus 2 cover glass Always-on display with At a Glance and Now Playing Up to 1600 nits (HDR) and up to 2200 nits (peak brightness) >1,000,000:1 contrast ratio HDR support Full 24-bit depth for 16 million colours Battery and chargingBeyond 24-hour battery life Up to 72-hour battery life with Extreme Battery Saver Minimum 4,950 mAh Typical 5,050 mAh Fast charging - up to 50% charge in about 30 minutes - using Google 30 W USB-C Charger with USB-PD 3.0 (PPS) sold separately Qi-certified Fast wireless charging Battery Share Memory and storage12 GB LPDDR5X RAM 128 GB/256 GB/512 GB UFS 3.1 storage ProcessorsGoogle Tensor G3 Titan M2 security coprocessor Rear camera50 MP Octa PD wide camera 1.2 ?m pixel width ƒ/1.68 aperture 82 field of view 1/1.31? image sensor size 48 MP Quad PD ultrawide camera with autofocus 0.8 ?m pixel width ƒ/1.95 aperture 125.5 field of view Lens correction 48 MP Quad PD telephoto camera 0.7 m pixel width ƒ/2.8 aperture 21.8 field of view 5x optical zoom Super Res Zoom up to 30x Multi-zone LDAF (laser detect auto-focus) sensor Spectral and flicker sensor Optical + electronic image stabilisation on wide and telephoto Front camera10.5 MP Dual PD selfie camera 1.22 ?m pixel width ƒ/2.2 aperture Auto-focus 95 ultrawide field of view Camera featuresPro controls High-resolution images Ultra HDR Magic Editor Best Take Macro Focus Magic Eraser Photo Unblur Motion Mode Real Tone Face Unblur Panorama Manual white balancing Locked Folder Night Sight Astrophotography Top Shot Portrait...
We will shortly be reviewing the Google Pixel 8 Pro. Here are the general specifications on it, and you can also see more on their website here. Pixel's best pro camera yet. The Pixel 8 Pro camera system includes updated, pro-level cameras for better low-light photos, sharper selfies and Pixel's best zoom ever. And Pro controls enable advanced camera settings and full-resolution photography. Details about Google Pixel 8 Pro Cutting-edge video processing. Don't worry about a shaky or imperfect video. With Video Boost, colour, lighting, stabilisation and graininess are automatically adjusted to help improve overall quality. Video sounds even better, just like that. Sounds from cars, wind or construction can be disruptive in video. Audio Magic Eraser uses Google AI to reduce distracting sounds with a few taps, so you can hear the ones that you want. Group pics, perfected. Did someone blink or look away? Pixel's Best Take combines similar photos into one fantastic picture where everyone looks their best. Hear your caller clearly. With improved clear calling, Pixel reduces even more of your caller's background noise and enhances their voice. So you can hear them when they're in a crowded or noisy place.9 Extra protection when you're online. With VPN by Google One built in, Pixel helps protect your online activity no matter what app or web browser you use. DisplayFull-screen 6.7-inch (170 mm) display 20:9 aspect ratio Super Actua display (1344 x 2992) LTPO OLED at 489 PPI Smooth Display (1-120 Hz) Corning Gorilla Glass Victus 2 cover glass Always-on display with At a Glance and Now Playing Up to 1600 nits (HDR) and up to 2200 nits (peak brightness) >1,000,000:1 contrast ratio HDR support Full 24-bit depth for 16 million colours Battery and chargingBeyond 24-hour battery life Up to 72-hour battery life with Extreme Battery Saver Minimum 4,950 mAh Typical 5,050 mAh Fast charging - up to 50% charge in about 30 minutes - using Google 30 W USB-C Charger with USB-PD 3.0 (PPS) sold separately Qi-certified Fast wireless charging Battery Share Memory and storage12 GB LPDDR5X RAM 128 GB/256 GB/512 GB UFS 3.1 storage ProcessorsGoogle Tensor G3 Titan M2 security coprocessor Rear camera50 MP Octa PD wide camera 1.2 ?m pixel width ƒ/1.68 aperture 82 field of view 1/1.31" image sensor size 48 MP Quad PD ultrawide camera with autofocus 0.8 ?m pixel width ƒ/1.95 aperture 125.5 field of view Lens correction 48 MP Quad PD telephoto camera 0.7 m pixel width ƒ/2.8 aperture 21.8 field of view 5x optical zoom Super Res Zoom up to 30x Multi-zone LDAF (laser detect auto-focus) sensor Spectral and flicker sensor Optical + electronic image stabilisation on wide and telephoto Front camera10.5 MP Dual PD selfie camera 1.22 ?m pixel width ƒ/2.2 aperture Auto-focus 95 ultrawide field of view Camera featuresPro controls High-resolution images Ultra HDR Magic Editor Best Take Macro Focus Magic Eraser Photo Unblur Motion Mode Real Tone Face Unblur Panorama Manual white balancing Locked Folder Night Sight Astrophotography Top Shot Portrait mode Portrait Light Super Res Zoom Motion auto-focus Frequent Faces Dual exposure controls Live HDR+ Video and Audio4K video recording at 24 FPS, 30 FPS, 60 FPS AuthenticationFingerprint Unlock with under-display fingerprint sensor Face Unlock Pattern, PIN, password SensorsProximity sensor Ambient light sensor Accelerometer Gyrometer Magnetometer Barometer Temperature sensor Buttons and portsUSB Type-C 3.2 Gen 2 Power button Volume controls SIMsDual SIM (Single Nano SIM and eSIM) Media and audioStereo speakers Three microphones Noise suppression Spatial audio Connectivity and locationWi-Fi 7 (802.11be) with 2.4 GHz + 5 GHz + 6 GHz, 22+22 ColoursObsidian Porcelain Bay Hearing aid compatibilityHearing aid compatible. See g.co/pixel/hac. Security and OS updatesSeven years of OS, security and Feature Drop updates MaterialsScratch-resistant Corning Gorilla Glass Victus 2 cover glass Edgeless Corning Gorilla Glass Victus 2 matte back ...
Shownotes: Episode 00077! Schnapszahl! ;) Erst mit den üblichen News zu allem rund um E-Mobilität, Arbeitsplatznews, KI, Infrastruktur, Gaming, usw.! Damit seid ihr mal wieder up-to-date bei den Themen aus der Tech-Welt! :) Dann geht's direkt ab in die Themen: Chris hat diesmal die philosophische Frage mitgebracht ob es Atome wirklich gibt - oder viel mehr die Denkweise hinter der Frage…! Denn wir wollen ja keinen Schwurbel promoten! Oder ist es keiner? Welche Art der Erklärung ist richtig? Oder gibt es das gar nicht per se? Hört rein! :) Pati erklärt uns dann USB Power Delivery! Was ist das? Wie lahm halt USB früher geladen? Und was kann es heute? Vor allem: Warum schmilzt mir das Kabel und dieser kleine Stecker dabei nicht weg? PHYSICS! B-) Lernt ihr hier und heute! Der Dummschnack wird dann noch für ein paar Rants genutzt und wie immer etwas übers Zocken gequatscht. ;) Ansonsten wie immer: Sharen, Kommentieren, uns-wissen-lassen-dass-ihr-da-seid (das ist beim Podcast gar nicht so einfach! :D)! Schreibt uns einfach auf Insta oder ne Mail unter jasiapodcast@gmail.com oder kommentiert bei Spotify direkt unter der Folge! :) Tschüss minnander! ;) Unsere Links: Unser Discord-Server: http://discord.ja-sia.de Instagram: https://www.instagram.com/jasiapodcast/ Facebook: https://www.facebook.com/jasiapodcast/ Mail: jasiapodcast@gmail.com Kapitel: 00:00:00 Intro 00:02:17 Vorgeplänkel 00:07:10 News 00:56:48 Themenvorstellung 00:59:03 Thema 1: Gibt's Atome wirklich? 01:40:38 Thema 2: Schnell nomma das Handy laden // Wie funktioniert USB-PD? 02:04:00 Dummschnack 02:29:14 Zusammenfassung Links zur Sendung: Kleid mit Displays: https://www.youtube.com/watch?v=EvGquKkSFMM YT Bill Gaede https://www.youtube.com/watch?v=KiDwqnanAYA Folge direkt herunterladen
This week's EYE ON NPI stands alone as a fantastic new solution for high power charging of large battery packs and also power boosting from battery to system: it's ADI/Maxim's MAX77789 Standalone 3.15A Charger (https://www.digikey.com/en/product-highlight/a/analog-devices/max77789-standalone-3-15a-charger), an all-in-one power management IC that lets you ditch DC power plugs and simplifies your BOM, at an excellent price. We'll also be covering the MAX77787 (https://www.digikey.com/short/wzv7095b) which is the fraternal-twin-sister product: using I2C instead of resistor settings for configuration. We've been covering USB Type C PD sinks and supplies for about a year here on EYE ON NPI & The Great Search, they're an excellent way to ditch those DC barrel jack power supplies (https://learn.adafruit.com/usb-pd-hacks/) and allow folks to use a single connector and standard power supply (https://www.youtube.com/watch?v=C90UnNAlCFQ) for various voltages, from 5V-20V at up to 5A. There's plenty of chips that will connect to a PD source and negotiate that voltage for you (https://www.youtube.com/watch?v=yQea9IEmf28) but now we can start to take advantage of USB PD for battery charging as well! This week's dynamic duo does pretty much everything for battery management. As devices get more complex, and battery cost goes down, the packs included in products are getting bigger. If you're trying to charge a 5Ah battery at standard 5V/1A rates, it will take at least 5-8 hours to do so, when folks really want 1-2 hour charge rates. The MAX77789 and MAX77787 have a buck converter that will deliver up to 3A to the battery for 3x faster charging. But, if you try to draw 3A from a USB 5V power cable, that built-in resistance will cause a voltage droop - remember we need at least 4.5V to have the headroom for charging up to 4.2V or 4.35V Lithium batteries. Thus, these chips use USB PD (https://learn.adafruit.com/understanding-usb-type-c-cable-types-pitfalls-and-more) to request higher voltages when available: 9V or 12V means that we can draw less current to get the same amount of power, which means less resistance loss over the cabling. For pre-C chargers, such as Samsung or Apple or Quick Charge (https://learn.adafruit.com/understanding-usb-type-c-cable-types-pitfalls-and-more) the USB D+/D- pins are used. In such cases where you want to have the data pins available for USB data/sync, you'll need something like the MAX20334 (https://www.digikey.com/short/p8b23vf3) data line switch to flip the pins back to your MCU. The MAX77789 uses resistors on the IFAST, ISET and INLIM lines to set the charge rate, timeout, and pack float voltage, the MAX77787 uses I2C. Both have a couple configuration pins, and LEDs for status monitoring. Both have the ability to also be turned into a boost converter - you can't use both charging and boosting at the same time, but since you can use the SYS voltage when connected to USB, you'll have at least 5V either way. The booster is fixed to 5.1V output. On the '89 the boost is enabled by GPIO, the '87 enables it over I2C. Both chips are available in 0.4mm pitch BGA - which means pad-in-via and multi-layer boards in order to pass the inner configuration traces out. Many of the traces are tripled-or-quadrupled to provide the current carrying capability of 3A charge and 6A peak discharge. An eval board is also available (https://www.digikey.com/short/4dc80hwz) which makes quick verification easy. For the I2C configuration version there's also desktop software to try out various settings - the standalone version has jumpers so you can attach any resistor value. Both the ADI/Maxim MAX77789 (https://www.digikey.com/short/j7zhtj4h) and MAX77787 (https://www.digikey.com/short/wzv7095b) Standalone/I2C 3.15A Chargers are in stock right now at DigiKey for immediate shipment. It's great to see forward momentum in chip design releases now that the shortages have abated: only a year ago we were scrambling for diodes and op-amps and now we have a wealth of great new products to choose from! Order one of these powerful Lithium battery management chips today and you'll have it shipped immediately so that you can start integrating it into your new design by tomorrow afternoon.
We wrote a driver this week for the HUSB238 USB PD sink chip https://blog.adafruit.com/2022/05/04/plug-n-play-usb-type-c-dummy-pd/ - this IC is neat in that you can either use jumpers (really, resistor selection) to set the desired PD voltage and current ooooor you can use I2C for dynamic querying and setting. we have a wall adapter that can provide almost-all-PD voltages: 5/9/12/15/20 only 18 is skipped. The HUSB plugs into the USB C cable and, over the CC lines, will negotiate the PD request and commands. For example, we can ask what voltages are available and then iterate over the options here: a multimeter displays the output voltage to prove it works! This can be a handy chip for projects where you need a lot more than 5V @ 2A power: this adapter can give up to 20V at 5A - yes 100W over USB C - and you could buck that down to get a toooon of current at 5V or 12V if that's needed. Arduino library and example code is here https://github.com/adafruit/Adafruit_HUSB238 . This is also one of the first shipping boards using an OpenAI ChatGPT assisted library https://chat.openai.com/share/d05c963d-b610-4eef-ad98-05656a33e118 https://chat.openai.com/share/a276ce74-f810-4dba-a324-e9fd1545085f Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #adafruit #arduino #HUSB238 #opensource #opensourcehardware #USBPD #usbc #powerdelivery #techinnovation #smartchip #electronics #projectpower #voltagecontrol #driverupdate #usbchip #hardwaredevelopment #openai #chatgpt
Z czym kojarzy się Wam końcówka roku? Z wydatkami? Co racja, to racja, świąteczny czas to przecież również nerwowa bieganina za upominkami, których celem jest wywołanie uśmiechu na twarzach i radości w sercach naszych bliskich. Kolejny raz dzielimy się z propozycjami zakupów dużych i małych, drogich i …mniej drogich gadżetów, które naszym zdaniem sprawdzą się jako wartościowe i praktyczne podarunki. Ciekawi jesteśmy Waszych typów! Ładowarka TRAVEL QUAD GaN 4 Ports 100W Charger with USB PD and QC 3.0 | ceneo.pl Ładowarka Kostka Anker 3-w-1 z MagSafe Adapter DIGITUS USB Type-C™ na Gigabit Ethernet 2,5G, USB-C™+ USB A | ceneo.pl Satechi Thunderbolt 4 Dock | shelter.pl CalDigit Thunderbolt 4 Element Hub | ceneo.pl Adapter Rolling Square inCharge® 6 | ceneo.pl Przewód 4K USB-C do USB C 3.1 Gen 2 Przewód 20V 100W 40Gbps USB C do USB C / Thunderbolt szybka transmisja danych + ładowanie Adaptery USB-C do USB-C (męski, żeński, prosty, kątowy) Adapter USB3.0 Micro USB do USB-C Adapter Mini USB do USB-C Adapter USB-B do USB-C Adapter USB-C do Micro USB Adapter ROCK USB-C do Lightning Power Bank Belkin BoostCharge Plus 10K USB-C | ceneo.pl Koncentrator wieloportowy Verbatim USB-C | ceneo.pl Uchwyt samochodowy do ładowarki Apple MagSafe Spigen MagFit Car Mount | spigen.pl Etui do iPhone Peak Design Everyday Case Plecak antykradzieżowy Bobby Pro Anti-Theft | ceneo.pl Klawiatura składana mini AVATTO Bluetooth 5.1 Pamięć NAS Synology DiskStation® DS923+ Router mesh Synology WRX560 | ceneo.pl PerfectBlue.pl – gadżety Partnerem applejuice i sponsorem podkastu kompot jest firma Synology. Nasz podkast znajdziecie w Apple Podcasts (link), możecie też dodać do swojego ulubionego czytnika RSS (link), obejrzeć na YouTube (link), wysłuchać w serwisach: Spotify (link), Google Podcasts (link), TuneIn (link), Overcast (link), Castbox (link), PlayerFM (link), Pocket Casts (link), myTuner (link) lub przesłuchać bezpośrednio w przeglądarce (link). Zapraszamy do kontaktu na Twitterze: Remek Rychlewski @RZoG. Marek Telecki @mantis30. Natomiast całe przedsięwzięcie firmuje konto @ApplejuicePl.
サンワ、USB PD給電にも対応した容量2万mAhのモバイルバッテリーを発売 最大60W出力対応。 サンワサプライは8月19日、最大60Wの出力をサポートしたUSBモバイルバッテリー「BTL-RDC24」の販売を開始した。想定販売価格は2万7500円(税込み)となる。
This week's EYE ON NPI is very adaptable - it's CUI Inc's 30 W Desktop USB PD Adapters (https://www.digikey.com/en/product-highlight/c/cui/30-w-desktop-usb-pd-adapters) which have up to 30 Watts of output with a variety of voltages, so they can be used in multiple product designs to make your inventory and procurement simpler! These power adapters will help you transition your products from DC jacks to USB C, which has power negotiation all in one consistent, well-recognized connector. We've covered DC plug adapters on EYE ON NPI before. Just about every product in the world uses these ubiquitous 'barrel jack' connectors for power (https://www.digikey.com/en/products/filter/ac-dc-desktop-wall-adapters/130): often 5.5mm outer diameter / 2.1 or 2.5mm inner (https://www.digikey.com/en/products/detail/cui-devices/PJ-003A/96969). These connectors are so popular that they don't really 'mean' anything when you see them other than "power connector". There's no inherent voltage, polarity or current capability that is indicated by a barrel jack. You could have 5VDC center-positive 5A adapter (https://www.digikey.com/en/products/detail/cui-inc/SDM36-5-U-P5/8547877) or you could have a 9VAC 300mA adapter, all with the same connector. Only by careful reading and matching of the labels can you verify which adapter you have matches with which product - and if you lose the adapter it could be a real pain to get a replacement. That's where USB Type C has a lot of potential to improve and simplify this issue: folks end up being scared to toss out their power adapters because you never know when you need it or what the matching devices is, even years later. If, instead, we had one power adapter and cable that would be usable for any product, that would deliver the right voltage, we could mix and match adapters without worrying about under-powering or over-volting. A lot of mobile devices have started to go this way with USB mini or micro B ports, cell phones being the most popular: all USB ports are basically 5V 1A (https://www.digikey.com/en/products/detail/cui-inc/SWI5-5-N-I38/5287192) and if you have something running off of a Lipoly battery, this is plenty to keep you topped up. But for larger devices, ones with displays or motors, or larger battery packs, 5W (or 10W on a fancy high current adapter) is not going to be enough. And you don't necessarily want 5V input! If you have a backlight that requires 12V or a battery pack that is 8.4V it's going to be expensive and wasteful to try and boost 5V USB up to 12V. USB C's Power Delivery spec is a great solution: it can provide anywhere from 5V to 20V DC, at up to 100W if the power adapter is chunky enough. CUI's awesome blog has a great post about the power delivery specifications with clear text and diagrams (https://www.cui.com/blog/usb-type-c-pd-and-pps) for more info - in particular watch out that you have a current limitation or 3A or 5A at each voltage so you'll never be able to get 5V 20A = 100W. Instead you'd get 20V at 5A. However, if your voltage / wattage use case lies within the PD requirements, you're good to go! You can use a standard USB C connector (https://www.cuidevices.com/catalog/interconnect/connectors/usb-connectors), standard USB C power cables (https://www.cuidevices.com/catalog/interconnect/cable-assemblies/usb-cables?[0].sn=Connector%201&[0].sv=Type%20C%20Plug) - all available from CUI and the CUI 30 W Desktop USB PD Adapter (https://www.digikey.com/short/v0f7fqm2) as the power supply. Best of all, Digi-Key has tons of CUI 30 W Desktop USB PD Adapters (https://www.digikey.com/short/v0f7fqm2) in stock, the version we're linking to comes with a USA power cable, but they also sell a version without a cable (https://www.digikey.com/en/products/detail/cui-inc./SDI30C-Q-UTB-CUB/16376426) so you can swap out with a UK, EU or other wall plug. Don't forget to also get a high quality CUI USB Type C connector (https://www.digikey.com/short/w23hh4m4) to go with. Order today for immediate shipment!
This week's EYE ON NPI is very adaptable - it's CUI Inc's 30 W Desktop USB PD Adapters (https://www.digikey.com/en/product-highlight/c/cui/30-w-desktop-usb-pd-adapters) which have up to 30 Watts of output with a variety of voltages, so they can be used in multiple product designs to make your inventory and procurement simpler! These power adapters will help you transition your products from DC jacks to USB C, which has power negotiation all in one consistent, well-recognized connector. We've covered DC plug adapters on EYE ON NPI before. Just about every product in the world uses these ubiquitous 'barrel jack' connectors for power (https://www.digikey.com/en/products/filter/ac-dc-desktop-wall-adapters/130): often 5.5mm outer diameter / 2.1 or 2.5mm inner (https://www.digikey.com/en/products/detail/cui-devices/PJ-003A/96969). These connectors are so popular that they don't really 'mean' anything when you see them other than "power connector". There's no inherent voltage, polarity or current capability that is indicated by a barrel jack. You could have 5VDC center-positive 5A adapter (https://www.digikey.com/en/products/detail/cui-inc/SDM36-5-U-P5/8547877) or you could have a 9VAC 300mA adapter, all with the same connector. Only by careful reading and matching of the labels can you verify which adapter you have matches with which product - and if you lose the adapter it could be a real pain to get a replacement. That's where USB Type C has a lot of potential to improve and simplify this issue: folks end up being scared to toss out their power adapters because you never know when you need it or what the matching devices is, even years later. If, instead, we had one power adapter and cable that would be usable for any product, that would deliver the right voltage, we could mix and match adapters without worrying about under-powering or over-volting. A lot of mobile devices have started to go this way with USB mini or micro B ports, cell phones being the most popular: all USB ports are basically 5V 1A (https://www.digikey.com/en/products/detail/cui-inc/SWI5-5-N-I38/5287192) and if you have something running off of a Lipoly battery, this is plenty to keep you topped up. But for larger devices, ones with displays or motors, or larger battery packs, 5W (or 10W on a fancy high current adapter) is not going to be enough. And you don't necessarily want 5V input! If you have a backlight that requires 12V or a battery pack that is 8.4V it's going to be expensive and wasteful to try and boost 5V USB up to 12V. USB C's Power Delivery spec is a great solution: it can provide anywhere from 5V to 20V DC, at up to 100W if the power adapter is chunky enough. CUI's awesome blog has a great post about the power delivery specifications with clear text and diagrams (https://www.cui.com/blog/usb-type-c-pd-and-pps) for more info - in particular watch out that you have a current limitation or 3A or 5A at each voltage so you'll never be able to get 5V 20A = 100W. Instead you'd get 20V at 5A. However, if your voltage / wattage use case lies within the PD requirements, you're good to go! You can use a standard USB C connector (https://www.cuidevices.com/catalog/interconnect/connectors/usb-connectors), standard USB C power cables (https://www.cuidevices.com/catalog/interconnect/cable-assemblies/usb-cables?[0].sn=Connector%201&[0].sv=Type%20C%20Plug) - all available from CUI and the CUI 30 W Desktop USB PD Adapter (https://www.digikey.com/short/v0f7fqm2) as the power supply. Best of all, Digi-Key has tons of CUI 30 W Desktop USB PD Adapters (https://www.digikey.com/short/v0f7fqm2) in stock, the version we're linking to comes with a USA power cable, but they also sell a version without a cable (https://www.digikey.com/en/products/detail/cui-inc./SDI30C-Q-UTB-CUB/16376426) so you can swap out with a UK, EU or other wall plug. Don't forget to also get a high quality CUI USB Type C connector (https://www.digikey.com/short/w23hh4m4) to go with. Order today for immediate shipment!
#deskofladyada #thegreatsearch #adafruit We are a-glow with some fun samples this week! We got some neat flexible and non-flex LED filaments we're checking in various colors and styles. Fun fact - we got some LED filaments years ago to stock but they only came in 70V and so we ended up not putting them into the shop because they'd be too annoying to use. We also got some nifty magnetic usb cables and a programmable USB PD cable! The Great Search - A good beginner oscilloscope https://www.digikey.com/short/80w8j2z4 We have folks ask us what's a good beginner 'scope to purchase. Turns out that even with a $500 budget, you can get a pretty nicely spec'd out scope that will help you tons in debugging projects. Since oscilloscopes come in just about every configuration, a lot of picking out a scope is going to be deciding what trade-offs you want with respect to channels, bandwidth/sample rate, and memory size. Let's check out what you can get on Digi-Key to kickstart your electronics workbench! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------
エレコムが「USB PD EPR」対応のUSB Type-Cケーブルを発売 3880円から。 エレコムは5月下旬、USB PD(Power Delivery)の新リビジョンで定められた「EPR(Extended Power Range)」の認証を取得したUSB Type-Cケーブルを発売した。税込みの想定販売価格はUSB 2.0規格に準拠するものが3880円から、USB4規格に準拠するものが8480円となる。
We got a few samples of these very nifty USB C cables - there's a Type C plug on one end and a DC 2.5mm/2.1mm on the other. On the plug is etched a voltage and current range. inside is a USB C PD chip that negotiates to try and get the selected voltage and current out of a USB C power plug with Power Delivery management, and it works! we got 9V, 12V, 15V and 20V cables and tested it with our 3A test load and the cables had almost no drop. these could be super handy for getting significant power from USB C without having to do the noodling of programming or configuring a PD chip. coming soon to the adafruit shop! Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ ----------------------------------------- #adafruit #usb #usbc
On this week's Desk of Ladyada we're celebrating spring - the tulips and cherry blossoms are blooming all over NYC this weekend. We took some cute spot-color pictures with the KB2040 for an upcoming freebie promo. We also got some samples of CH9102 which work great as replacements for CP210x which is good because we've had some difficulty getting the chips we've booked on allocation. We also found a very nice USB PD sink chip that has I2C and pin-select for voltage and current, and designed a breakout! The Great Search - Pink or purple LEDs! https://www.digikey.com/short/d7j3rdmw NYC's cherry blossom trees are in full bloom and we were inspired to perhaps get some pretty 0603 LEDs that we could use as indicators, especially on our pink KB2040 PCBs. This great search will show you some tips on reading the datasheet for an LED to verify the wavelength is a color you like #deskofladyada #thegreatsearch #adafruit Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------
We have been on the lookout for a Sony Flamingo - a very retro-futuristic turntable that can play singles or LPs using a funky minimalist design. It is a gorgeous piece of machinery. Meanwhile, we know folks like using a Raspi to make a 'pihole' ad/malware blocking DNS server but pi's are hard to get, so we looked at turning a Feather ESP32-S2 TFT into an 'esphole' and found a great project to fork off and tweak https://github.com/s60sc/ESP32_AdBlocker We've added mass storage config, and a TFT display to show the IP address and status. We also threw together a quick breakout for a very nice precision magnetometer the MMC5983 https://www.digikey.com/short/m43v5mtj and we're taking a peek at an interesting USB PD chip the HUSB238 which has a resistor set for current and voltage as well as I2C configuration port! #deskofladyada #thegreatsearch #adafruit Visit the Adafruit shop online - http://www.adafruit.com ----------------------------------------- LIVE CHAT IS HERE! http://adafru.it/discord Adafruit on Instagram: https://www.instagram.com/adafruit Subscribe to Adafruit on YouTube: http://adafru.it/subscribe New tutorials on the Adafruit Learning System: http://learn.adafruit.com/ -----------------------------------------
The European Union is proposing a mandate requiring USB-C ports on all phones, tablets, handheld gaming consoles, headphones and bluetooth speakers. For devices with fast charging the EU mandate calls for only USB PD to be used. Additionally manufacturers will be forced to sell phones that do not include power adapters in the box. See my USB-C confusion video: http://lon.tv/usbconfusion and subscribe! http://lon.tv/s VIDEO INDEX: 00:00 - Intro 00:23 - History of the EU's interest in charging ports 01:53 - The EU's Proposed Mandate 03:43 - Mandate: USB-C Ports Required 05:04 - Mandate: Chargers to be "Unbundled" from Phone Sale 06:08 - Mandate: USB-C Explanation to Consumers 08:15 - Prediction: Apple will get rid of the port! 08:37 - What About Wireless Charging 11:14 - What's Next? 13:12 - Supporter Thank Yous 13:54 - Helping The Channel 14:07 - My Other Channels 14:54 - Conclusion Subscribe to my email list to get a weekly digest of upcoming videos! - http://lon.tv/email See my second channel for supplementary content : http://lon.tv/extras Join the Facebook group to connect with me and other viewers! http://lon.tv/facebookgroup Visit the Lon.TV store to purchase some of my previously reviewed items! http://lon.tv/store Read more about my transparency and disclaimers: http://lon.tv/disclosures Want to chat with other fans of the channel? Visit our Facebook Group! http://lon.tv/facebookgroup Want to help the channel? Start a Member subscription or give a one time tip! http://lon.tv/support or contribute via Venmo! lon@lon.tv Follow me on Facebook! http://facebook.com/lonreviewstech Follow me on Twitter! http://twitter.com/lonseidman Catch my longer interviews and wrap-ups in audio form on my podcast! http://lon.tv/itunes http://lon.tv/stitcher or the feed at http://lon.tv/podcast/feed.xml We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. --- Support this podcast: https://anchor.fm/lon-seidman/support
主持人:陳鳳馨 來賓:豐銀投顧資深分析師 何金城 主題:台北股市盤前解析| ①聯電入股頎邦大結盟的意義 ②高速傳輸 USB4.0 與 快充 USB PD 商機 節目時間:週一至週五 7:00-9:00am 本集播出日期:2021.09.06 #陳鳳馨 #金融市場財經新聞即時評析 #台股盤前
今日のテーマ「災害時にも役立つ急速充電USB PD、軽量、コンパクト!持ってて損はないね」
One more thing! In Folge 31 fiebern die ApfelNerds dem nächsten Apple-Event entgegen, dass am 10.11.2020 stattfinden, und die heiß ersehnten, ersten Apple Silicon-Macs bringen soll. Außerdem sprechen sie über MagSafe und USB-PD 3.0-Netzteile, über die 12 W-Beschränkung bei MagSafe und dem iPhone 12 mini, über MagSafe Duo, Saschas Besuch im Apple Store, den Start von Apple One, den AppClip bei Exxon, die Luftqualität in korrelation zur iPhone-Produktion, die Preiserhöhung von Netflix, über die gepairten iPhone 12-Kameras, über die iOS 14, watchOS 7.1 und tvOS 14.2 Release Candidates, und über Mark Zuckerberg, der den Ruin der Ökonomie durch Ad-Blocking herbei beschwört.
The TS80P is the upgrade to the TS80, Dave’s previous favorite portable soldering iron. But with added USB-PD and 30W vs 18W. Various Aliexpress stores: https://s.click.aliexpress.com/e/_BfZODpxj https://s.click.aliexpress.com/e/_dUG2CxP TC66 USB-C PD Power Monitor/Logger: https://s.click.aliexpress.com/e/_Bf8wne37 Forum: https://www.eevblog.com/forum/blog/eevblog-1319-new-ts80p-portable-usb-pd-soldering-iron-review/
USB-PD is a newer specification that deals with the power that can be derived from a USB port. It’s quite an important spec and one that has lots of potential. Unfortunately, it’s one of the specs that’s not well understood. To get a better understanding for myself (in turn, for you), I invited Doug Bailey, a vice president at Power Integrations to be my guest for this week’s Five Minutes with…podcast.
概要やアプリリンクまとめ: http://bit.ly/2OxsBuH 感想や質問、リクエストなどはTwitterのハッシュタグ #goryugocast にお送りください。Anchorからのボイスメッセージも受け付けています。 収録機材や収録方法、各配信の概要などはScrapboxにて詳細を公開しています。 scrapbox.io/goryugocast/
Your source for all things Nintendo 3 days a weekSponsored By:OPSeat: Head over to https://www.runjumpstomp.com/opseat to directly support the show, and get a fantastic gaming chair that can support you! I'm sitting in one right now, and its great.Support Nintendo Switch CraftLinks:Patreon — This episode of SwitchCraft is brought to you by Rock Roberge — Support SwitchCraft and my other content for as little as a dollar and get exclusive rewards at https://www.patreon.com/runjumpstompWatch the Live Show! — Switch Craft is recorded Live 3 times a week on Tuesday and Thursday at 3pm US Eastern and on Saturday at whatever time I can get to it. Tune in live at https://www.twitch.tv/runjumpstompJohnny P wrote in about my wife's Etsy shop. — Hi RJS, I will save you from shamelessly promoting your wife’s etc shop. I am more than 100% satisfied. I have had an awesome doc sock for months now and still love it. It is the best switch accessory I own. PS: I had a slight custom request, no problem just let them know what you want. Thanks again for the sock"The Switch is not USB-C compliant, and overdraws some USB-PD power supplies by 300%" by Nathan K(Links in description) : NintendoSwitch — "The +Nintendo Switch Dock #USB #TypeC power supply is not USB-PD spec compliant. As a result it does not "play nice" with other #USBC devices. This means you should strongly consider only using the Nintendo Switch Dock adapter only with the Nintendo Switch (and Dock). Additionally, it also seems the Nintendo Switch Dock does not "play nice" with other USB-PD chargers. This means you're forced to use a Nintendo-brand power supply."Nintendo Comments On Third-Party Docks Bricking Switch Systems - Nintendo Life — Nintendo (recommends) that Switch owners only buy officially licensed Switch products . . . Unlicensed products and accessories do not undergo Nintendo’s testing and evaluation process. They might not work at all with our game systems, and they could have compatibility problems with certain games, the Nintendo Switch system itself, and other licensed accessories and peripherals. “(Nyko is) aware of the issue some Portable Docking Kit owners are facing after updating the firmware on their Nintendo Switch to version 5.0. Though further testing is still required to determine the exact root cause of the problem, we believe it is related to the way the Switch handles AV output for an external TV/monitor while the console is docked on the Portable Docking Kit.”Square Enix To Re-release Some Games On The Switch From Collective Project | NintendoSoup — “At t --- This episode is sponsored by · Anchor: The easiest way to make a podcast. https://anchor.fm/app
Power Systems Design, Information to Power Your Designs
Fire Sticks The next Hardware and Electronics Engineering Meetup page is live and will be on June 28th. Please RSVP if you plan on attending! The Stanford ValBal launched again with avionics components from MacroFab! You can see a live video on our Facebook page from earlier today and as always, track it with this site. Also check out episode 64 of the MEP where we have Sasha Maldonado and Paige Brown of the Standford Student Space Initiative! Parker Tested a new serial LED board for the pinball platform CLP6C-FKB LED WS2801 Draws 60mA LED 8mA standby current Laser the V-scored PCBs apart Finishing up writing the last of the EFM8 articles that Parker started last October Stephen Synth works but doesn’t. Not getting ACF, something isn’t biased just right Stephen will rip out some strip board and create an off board filter Final version will have two envelopes The current envelope works but Stephen doesn’t like it Mutable Instruments Shruthi 1 Pick Of the Week (POW) PD Buddy Sink : USB Power Delivery for everyone - Hackaday.io Projects Built by Clayton Hobbs Smart power jack that plugs into Power Delivery enabled power sources Tell it what voltage and current you need and it talks to the to any USB PD power supply to get you the juice Internet of Fidget Spinners - HackADay Built by Matthias ESP8285 for communitcation Accelerometer to measure wobble and an optical switch to measure the rotation speed POV - persistence of vision for graphics Project PageTags: CLP6C-FKB, Fidget Spinners, LED, MacroFab, macrofab engineering podcast, MEP, PD Buddy Sink, Peratech, Pinball, Podcast, SP-200-10, Synth, USB Type-C, ValBal, Worlds Heaviest Weight, WS2801, Z-Mouse
Hakuro Matsuda さんをゲストに迎えて、WWDC 2017 について話しました。 Show Notes WWDC Keynote, June 2017 iMac - Apple USB Power Delivery NEW YubiKey 4C featuring USB-C revealed at CES 2017 Google to OEMs: Don’t use Qualcomm Quick Charge; USB-PD is the future AMD Threadripper 1920 12-Core CPU & Vega 16GB/8GB Cards Leaked Intel’s Core i9 Extreme Edition CPU is an 18-core beast iMac Pro Apple's Metal 2 API Adds External GPU, VR Support to macOS iMac memory specifications APFS Introduction Craig (@_HairForceOne) macOS High Sierra Preview Metal 2 Indirect Drawing ARKit Apple Acquires Augmented Reality Company Metaio Tango Nvidia G-SYNC – variable refresh rate technology High Efficiency Video Coding, H.265, and 4K compression explained MPEG LA VP9 HLS Vs Dash Apple introduces a completely redesigned App Store “MP3 is dead” missed the real, much better story LAME MP3 Encoder Core ML Google Announces Tensorflow Lite: A Neural Network Library for Mobile Phones Converting Trained Models to Core ML
Naoki Hiroshima さん、Kazuho Okui さんをゲストに迎えて、AirPods, Macbook Pro, Swift 3, USB-C, Google 翻訳、大統領選などについて話しました。 Show Notes Apple delays AirPods launch How to check an API is available in Swift for iOS and macOS Yammer iOS App ported to Swift 3 Tatsuhiko Miyagawa's blog — The new Macbook Pro On the road with the 13-inch MacBook Pro USB-C and Thunderbolt 3: Here's everything you need to know What did the SD card ever do to Apple? Philip Schiller talks computers, touchscreens and voice on the new MacBook Pro Google to OEMs: Don’t use Qualcomm Quick Charge; USB-PD is the future Apple Drops Prices of 4K and 5K LG Displays by 25 Percent Synergy - Mouse and keyboard sharing software Tim Cook on iPad Pro: 'Why would you buy a PC anymore?' 「Google翻訳」にニューラルネット機械翻訳技術を採用 A Neural Network for Machine Translation, at Production Scale 機械翻訳と意味 「Love trumps hate」を「トランプ嫌い!」 Clinton's Popular-Vote Lead Is Going to Get a Lot Bigger Maryland sidesteps electoral college After a Fraught Election, Questions Over the Impact of a Balky Voting Process 米連邦最高裁の未来は? スカリア判事死去で政治駆け引き California Proposition 64, Marijuana Legalization greatagain.gov Trump: The Art of the Deal How the White House will hand over social media accounts to Clinton or Trump ピーター・ティール氏、トランプ次期大統領の政権移行チームに正式参加 Yes California Independence Campaign Jesusland map Donald Trump pulling colored flags from his nose JavaScriptはキリスト教だった……!?